2015 KME Log book info Flashcards by Daniel Bui

F377? Retain how many copies?

Preventative Maintenance Record / Retain the last six copies

How well did you know this?

Not at all

Perfectly

F-708?

Inventory

How well did you know this?

Not at all

Perfectly

The MDC will continue to draw electrical current (approximately _____) even though the battery master switch is turned OFF.

7 to 8 amps

How well did you know this?

Not at all

Perfectly

Maximum inlet restriction for a new air cleaner is ___” H2O. If the gauge reads __” H2O, check for restrictions.

10 / 25

How well did you know this?

Not at all

Perfectly

It has a 5.12” bore and a 5.91” stroke, with a total piston displacement of ___ cubic inches.

726

How well did you know this?

Not at all

Perfectly

The best fuel economy is delivered between _____.

1200 – 1800 RPM

How well did you know this?

Not at all

Perfectly

Regeneration is the process of converting soot collected from in the aftertreatment DPF into ____.

carbon dioxide

How well did you know this?

Not at all

Perfectly

Passive Regeneration — Occurs when the exhaust temperatures are____ to oxidize soot collected in the aftertreatment DPF faster than the soot is being collected.

naturally high enough

How well did you know this?

Not at all

Perfectly

The exhaust temperature during a normal active regeneration event could reach___ under certain conditions.

1100º F and possibly 1500º F

How well did you know this?

Not at all

Perfectly

DEF is a solution of ___ automotive grade urea and ____ deionized water.

32.5% / 67.5%

How well did you know this?

Not at all

Perfectly

DEF will freeze at ____.

12 F (-11C).

How well did you know this?

Not at all

Perfectly

DEF consumption will be approximately ____ of your fuel consumption.

How well did you know this?

Not at all

Perfectly

DEF has a shelf life of approximately ___ if stored in controlled temperatures between ___.

two years / 10 and 90 deg F.

How well did you know this?

Not at all

Perfectly

If DEF is stored outside of these temperatures it will last at least ____.

one year.

How well did you know this?

Not at all

Perfectly

In ___, all on-highway engines will include On-Board Diagnostics as a part of the emissions regulation requirement.

2013

How well did you know this?

Not at all

Perfectly

During regeneration, exhaust gas temperatures could reach ___ F, and exhaust system surface temperature could exceed __ F, which is hot enough to ignite or melt common materials, and to burn people.

1500º / 1300º

How well did you know this?

Not at all

Perfectly

During regeneration: Engine speed will increase and could possibly reach between ___ RPM.

1000 to 1500

How well did you know this?

Not at all

Perfectly

Do not idle in R (Reverse) for more than ____. Extended idling in R (Reverse) may cause transmission damage. Always select N (Neutral) whenever time at idle exceeds five minutes.

five minutes

How well did you know this?

Not at all

Perfectly

Gear 1 RPM? SPEED?

2100 / 14 mph

How well did you know this?

Not at all

Perfectly

Gear 2 RPM? SPEED?

2100 / 26 mph

How well did you know this?

Not at all

Perfectly

Gear 3 RPM? SPEED?

2100 / 36 mph

How well did you know this?

Not at all

Perfectly

Gear 4 RPM? SPEED?

2100 / 54 mph

How well did you know this?

Not at all

Perfectly

Gear 5 RPM? SPEED?

2000 / 66 mph

How well did you know this?

Not at all

Perfectly

Gear 6 RPM? SPEED?

1700 / 66 mph

How well did you know this?

Not at all

Perfectly

Max Speed

66 mph

If the engine fails to start within ___, release the starter button and allow the starting motor to cool for approximately _____ before trying again

15 seconds

If the engine fails to start after ____, an inspection should be made to determine the cause.

four attempts

If there is no oil pressure indicated within ___ seconds, stop the engine and check the lubricating system.

10 to 15

Try not to shut down the engine unless coolant temperature is ___ F or less.

195º

In the event air brake system pressure drops below approximately ___ a warning buzzer and light will come on.

65 psi

As soon as system air pressure increases past ____, the warning light and buzzer will shut-off.

65-75 psi

Use extreme caution when operating the vehicle with either air brake section charged to less than ___ or property or personal injury could result.

60 psi

The engine brake reacts quickly; it will activate or deactivate in less than ___ of a second.

1/4

After the battery voltage drops to a preselected setting (approximately ___), the engine throttle will be increased to compensate for the low voltage and electrical system loads.

12.8 volts

The fast idle output will remain ON for a minimum of 10 minutes and until ___ VDC is achieved.

13.0

An alarm sounds if a low-voltage condition (below ____) develops.

11.9 volts

If the low-voltage condition continues (for approximately ___), then the shedding of electrical loads will begin.

1 minute

A shed system (load) will not be recognized for _ minutes or until the unshed voltage setting is maintained for __ minute.

5 / 1

It is important to note that at minimum, when ALL electrical accessories are turned on and engine is running at idle (____ ), the alternator will be unable to keep up with the electrical demands placed on it thereby causing the air conditioning to be turned off.

500-750 rpm

The lights are the 12-volt Whelen Pioneer Series LED model and produce ____.

7000 lumens

Pump Recirculating Line Valve : water from the discharge side of the pump is sent to the water tank through a ___ line.

½”

When going from volume to pressure, slow the engine speed to reduce the discharge pressure to __ psi or less.

Open (pull) Tank to Pump Valve at Engineer’s Panel (allow ___ seconds for water to flow into pump.

Operate priming pump until main suction gauge shows a vacuum of approximately___ and main pressure gauge shows a positive pressure. NOTE: If you are not able to achieve prime within ___ , stop and investigate.

20” of Hg / 45 seconds

The water tank is a ___, Poly-Tank III, manufactured by United Plastic Fabricating (UPF)

500 gallon polypropylene tank

Water tank: All joints and seams are fused using ___ as required and tested for maximum strength and integrity

nitrogen gas

Maximum fill rate = __

500 GPM

Maximum inlet pressure for filling tank is __

100 PSI

Foam Pro is capable of proportioning foam between ___.

0.1% to 3.0%.

Foam Concentration / Max Water Flow | 0.2% =

1300 GPM

Foam Concentration / Max Water Flow | 0.5% =

520 GPM

Foam Concentration / Max Water Flow | 1.0% =

260 GPM

Foam Concentration / Max Water Flow | 3.0% =

85 %

Max Operating Pressure for foam is ____.

400 PSI

The minimum GPM flow needed to operate the Foam Pro System is ___.

30 gpm

Foam Pro : If the tank is | empty, the pump will not run for more than ____ minutes.

Foam Pro : In the event that the pump motor will not run or stalls for ___, the display will show “ERR.EL” to indicate that the pump is producing no feedback to the control signal.

10 seconds

When the fire pump is running, the foam pump cannot pump air efficiently against ___ backpressure.

100 to 150 psi

Foam Refill: The system comes with a foam pump/motor assembly, a refill wand with ___ , and a side-mount level indicator switch.

6 feet of 1" ID suction hose

Wagon Battery : Maximum flow and pressure is ____.

1250 gpm and 200 psi.

It is capable of flowing 1250 gpm while maintaining a FULL ___ of rotational travel (225° either side of center position).

450°

Wagon Battery : Elevation range is __ above horizontal and __ below.

90° / 45°

The monitor is made from hardcoat ____ and silver powder coat finish inside and out.

anodized ANSI 356.0-T6 aluminum

The OSCILLATE feature allows the user to program up to ___ of continuous movement of the horizontal and vertical axes.

65 points

The range of the wireless operator station is ___ and the handheld unit is powered by ___. When the battery voltage is low, the POWER light will begin to flash. At this point there are approximately ___ of continuous operation remaining. The handheld unit will automatically turn off after____ if no buttons are pressed.

500 ft / four (4) AA batteries / 3 hours / 5 minutes

Operate the hand pump and lift the cab to the full tilt position. The pump may need to be cycled ___ before the cab begins to lift.

20 or more strokes

Brakes : When the pads are new, the floating pin will be exposed approximately ____.

¾”to 1”.

Brakes : When the pin is sticking out __, the pads are worn to replacement condition. Call the shops once the floating pin is sticking out ¼” or less.

¼”

To manually release the spring brake chamber, unscrew (turn counter-clockwise) the ___ located at the end of the spring brake chamber utilizing a ___ or socket assembly.

½” diameter bolt / ¾” box end wrench

OL - - 0 X

Settling time too short.

OL - - 5 0

Engine speed (rpm) too low.

OL - - 5 9

Engine speed (rpm) too high

OL - - 6 5

Neutral must be selected.

OL - - 7 0

Sump fluid temperature too low.

OL - - 7 9

Sump fluid temperature too high.

OL - - 8 9

Output shaft rotation.

OL - - 9 5

Sensor failure.

A Cold Check may be made when the fluid temperature is ___.

60ºF – 120ºF.

To perform a Cold Check, do the following: | 1. Start and run the engine at idle ____ ) in N (Neutral) for about one minute.

(500 to 800 rpm

Perform a Hot Check at the first opportunity after normal operating temperature (___ ) is reached.

160ºF – 200ºF

To avoid damage to vehicle electronic components, voltage supplied to a vehicle’s electrical system must not exceed ___.

16.0 volts

Tires : Check pressures by gauge (____ )

105-psi front, 85-psi rear

Steering Box and Steering Linkage : Have an assistant move the steering wheel back and forth with short (___) rapid movements.

40 to 60

Report defect if belt tension is loose enough to allow more than___ deflection measured at a point midway between pulleys.

½”

Dry Vacuum Test : This should be at least 20” of vacuum. Stop priming pump and note amount of vacuum. (Should not drop more than ___ ).

10 in. Hg in 5 minutes

Tires shall be replaced when tread depth is at or less than ___ measured at any point on a major tread groove.

4/32”

Manual Pump Shift Procedure 1. Set maxi-brake. 2. Shift transmission to N (Neutral). 3. Move cab pump shift lever to the ___. 4. ___ engine.

center position / Shut down

Manual Pump Shift Procedure 5. Pull ______ (located on right side pump panel). 6. Start engine. 7. Place the________ “ON” position. 8. Shift transmission into D (Drive).

manual pump shift override handle / emergency override switch (right of steering column) in the

The discharge gates that are controlled by a handwheel, must be lubed with a hand operated lubed gun_____ . Give each zerk fitting about ___ with the handle operated lube gun.

. DO NOT USE AN AIR OPERATED LUBE GUN / five pumps