TADS Flashcards

(25 cards)

1
Q

Can the internal boresight be performed in flight?

A

Yes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

When should the internal boresight be performed?

A

As part of preflight procedures prior to use of laser weapons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What settings are automatically applied when initiating internal boresight?

A

The sight is set to TADS, the sensor to DTV, and the FOV to Narrow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What does squeezing the laser trigger to the second detent provide?

A

Ranging and designation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What does a flashing asterisk displayed in front of the range indicate?

A

Range is valid

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What is the minimum distance for range focus of the MTADS?

A

Range is invalid

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

How many bursts of laser energy are fired when pulling the RH ORT grip trigger to the first detent?

A

One burst

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What does the LMC require while maneuvering?

A

An accurate range

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

When should you perform an internal boresight for the TADS?

A

Prior to use of the laser and as often as necessary

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Will the FLIR boresight be performed if the DTV internal boresight fails?

A

No

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What do the TADS FOV Brackets surrounding the LOS reticle indicate?

A

Next FOV will be Zoom

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What field of view is normally used for target acquisition?

A

M or N; N or Z are used for target identification and engagement

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What causes the LOS reticle on flight symbology to flash?

A

LOS is invalid/selected, NVS is at its limit, or the gun system has failed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What happens if the FLIR is not cooled when DTV is boresighted?

A

The FLIR boresight will fail; however, the DTV boresight is valid

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

During a TADS Drift Null, where should the aim point remain?

A

Within the DTV NFOV for 30 sec

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What does the internal boresight align?

A

The TADS DTV to the laser LOS and the FLIR to the DTV LOS

17
Q

What must be performed successfully before the FLIR boresight?

A

The DTV boresight

18
Q

What does a solid asterisk displayed in front of the range indicate?

A

Range is valid

19
Q

How do you check the boresight correctors?

A

Access the DMS page, then select Boresight and the appropriate system

20
Q

How long does the initial automated internal boresight process take?

A

Approximately 2 min; subsequent boresights take approximately 30 sec

21
Q

Where are shared points stored in the 1000 point database?

A

In locations 100 to 950

22
Q

What is the maximum PRF laser frequency that may be entered?

23
Q

What is the maximum allowable registration error allowed?

A

+/-2 ft at 90 ft, estimated by using the open area of the LOS reticle, equivalent to 90 ft

24
Q

Where will a TGT XX message be displayed when storing a target with the TADS?

A

Weapons Inhibit for 4 sec

25
What happens to the TADS footprint symbol on the TSD when TADS is lasing?
Changes from green to white