Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

2018 MM > General Safety (ER 10-22-2018) > Flashcards

General Safety (ER 10-22-2018) Flashcards

1
Q

3 C’s in an emergency

A

Call, Check, Care

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How much potential stress can be placed on your back if a 75-pound object is lifted improperly?

A

up to 750 lbs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Most stretching exercises are done in repetitions of:

A

5 and held for 10 counts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Heel requirements for workboots

A

Heel must meet sole at 90 degrees and measures 3/4 inch in height at time of purchase, and no less than 1/2 inch at any time

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

impact and compression protection rating for work boots

A

I/75 C/75

75 pounds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

A properly adjusted hard hat can absorb what percent of the force of a blow?

A

75 percent

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

ANSI rating for Hard Hats

A

Z89.1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Hard hats should be cleaned with

A

soap and water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

3 types of gloves a technician might use

A

General work gloves
Climbing gloves
Insulated electrical gloves

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

how long are climbing glove gauntlets?

A

4 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Ear protection must be worn when a noise level exists above

A

90 dBA

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Safety glasses should be marked with what?

A

Z87.1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

2 scenarios when a face shield should be worn?

A

When handling batteries

Working around standby power supplies

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

MUTCD

A

Manual on Uniform Traffic Control Devices

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

OSHA Regulation for confined space

A

1910.146

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

In general, voltages greater than____are considered dangerous

A

50 V

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

FVDs will sound alarm if a voltage is over

A

50 V

18
Q

The FVD is equipped with filters to block

A

20Hz ringing and radio station signals

19
Q

Three basic types of signs that may be located in a work zone

A

Regulatory
Warning
Guide

20
Q

Traffic cones, drums, and barricades are all what types of devices?

A

Channelizing devices

21
Q

What is the 2 foot -15 foot rule?

A

Warning signs and channelizing devices may be omitted where the work space is behind a barrier, more than 2 feet (0.6 meters) behind the curb, or 15 feet (4.6 meters) from the edge of any roadway.

22
Q

Minimum height of a traffic cone

A

28 inches

23
Q

Minimum Drum height and diameter

A

at least 36 inches high and at least 18 inches in diameter

24
Q

What determines if a barricade is Type I, II, or III?

A

the number of horizontal rails

25
Q

What are Type III barricades used for?

A

road closure

26
Q

Three types of Warning Lights

A

Type A
Type B
Type C

27
Q

Type A warning light:

A

Low intensity flashing should be visible at 3000 feet on a clear night

28
Q

Type B warning light:

A

High intensity flashing,

Should be visible at 1000 feet on a clear night

29
Q

Type C warning light:

A

Steady burn, Should be visible at 3000 feet on a clear night

30
Q

any work zone that occupies a location more than 3 days

A

Long-Term Stationary

31
Q

daytime work that occupies a location for more than 1 and up to 3 days or any nighttime work lasting longer than one hour.

A

Intermediate-Term Stationary

32
Q

daytime operation that occupies a location for more than one, but less than 12 hours.

A

Short-Term Stationary

33
Q

work that occupies a location up to one hour

A

Short Duration

34
Q

work that moves intermittently or continuously

A

Mobile work zone

35
Q

4 basic components of a traffic control zone

A
  1. Advanced warning area
  2. Transition area
  3. Activity area (includes buffer and work spaces)
  4. Termination area
36
Q

The four types of tapers:

A

Shoulder, Shifting, Merging, and Downstream

37
Q

Safety vests should meet what ANSI standard?

A

107.2004

38
Q

per the MUTCD High Visibility Clothing should be visible at a distance of:

A

1000 feet

39
Q

OSHA telecommunications standard CFR number

A

1910.268

40
Q

What should a technician verify if approached by an OSHA Compliance Officer?

A

photo I.D. with serial number, signed by the Secretary of Labor

2018 MM (59 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions