*'93 Simon-LTI Flashcards Preview

Soriano-Tech > *'93 Simon-LTI > Flashcards

Flashcards in *'93 Simon-LTI Deck (27):
0

'93 Simon- Height of tiller cab, front cab, and full tilted cab?

*unknown*

*Unknown*
Tiller- 11'8"

Front cab- 10'5"

Full tilted cab- 16'2"

1

'93 Simon- Transmission temp normal operating range?

Max temp before needing to cool trans oil via high idle?

160°-220°F

250°F, if cooling procedures fail, notify shops

2

'93 Simon LTI- how long is the electrical cord reel mounted on the apparatus?

*unknown*

200 ft

3

On the '93 Simon-LTI, below what PSI will the "Low Air Pressure" indicator light illuminate?

60

4

'93 Simon- How many quarts of 15w-40 engine oil are needed for an oil change including the oil filter?

44 qts

5

'93 Simon- Normal voltage operating range with engine running?

*different from other rigs*

13.8-14.2v

6

'93 Simon- Normal engine coolant operating range?

160°-190°F

7

On the '93 Simon-LTI, the high water temperature indicator light will illuminate at what degrees?

220 degrees F

8

'93 Simon- Normal oil pressure operating range @idle, @1200 rpm and @2100 rpm?

10 psi min @ idle

35psi min @1200

45 psi min @ rated 2100 *log book also states 40-50 rpm @2100*

9

On the '93 Simon-LTI, if the "Air Cleaner Gauge" reads ___ inches of H2O, check for restrictions at the filter intake screen and notify shops if problem was not solved.

25 inches h20

10

'93 Simon LTI- what two degrees will the "Approaching Jackknife" indicator light illuminate?

62° and 90°

11

'93 Simon- How many quarts of 15w-40 engine oil are needed for an oil change not including the oil filter?

38 qts

12

'93 Simon- Length and width of apparatus?

*unknown*

Length- 54'10"

Width- 10'

13

On the '93 Simon-LTI, the "Low Engine Oil Pressure" indicator light illuminates when oil pressure drops below what psi?

3 psi

14

On the '93 Simon-LTI, what is the normal operating range for engine rpm?

Also, The driver should manually keep the rpm's between ____ and ____ when driving

1100-1600 rpm

1550-2100 rpm

15

'93 Simon LTI- What is the total outrigger spread when fully deployed?

*unknown*

16 ft

16

'93 Simon- fuel rank capacity?

50 gal

17

On the '93 Simon-LTI, what is the maximum air restriction for a CLEAN "Air Cleaner Gauge"?

10 inches h20

18

'93 Simon- Due to the nature of this engine, it may take more than ___ seconds of engine cranking to start.

5 secs

19

'93 Simon LTI- A red warning light (no audible alarm) will illuminate when transmission temperature reaches ____ degrees F.

250°F

20

'93 Simon- Due to the heat output created by the tillerbucket heater exhaust, keep objects away at least ___ inches

6"

21

'93 Simon: what is the tire psi for the front/rear/tiller tires?

110 front
90 rear
110 tiller

22

'93 Simon Rockwell brake system:

1. The disc brake system uses pads that are different thicknesses for the REAR brakes. Which pad is thinner and which is thicker? (Ie; inside pad vs outside pad) Also, what are the sizes of brake pads when new?

2. The FRONT brake pads, inner and outer, are identical, both are ____ of an inch when new and normally appear to be wearing at the same rate.

1. Inner pad is thicker (new 7/8")
Outer pad is thinner (new 9/16")
The rotor compensates for this difference by being thicker on the outboard side and thinner on the inboard side.

2. 5/8"

23

For a '93 hot engine shutdown (water temp operating range high):

Run rig at 900 to 1100 rpm (high idle) for 3 to 5 minutes or until temperature returns to normal, and then run it at idle for ____ seconds before shutdown.

30

This lets the oil carry away heat by circulation and gives the turbo time to cool

24

'93 Simon:

The outriggers should operate from the stowed to deployed position in ____ seconds or less

90

25

'93 Simon:

The tread wear bar indicator is the raised rubber portion located at the bottom of each tread groove, approximately ___ to ____ inches apart, around the circumference of the tire.

What is the width and height of the tread wear bar?

6 to 20"

1/2" wide by 3/32" high

26

'93 Simon logbook:

Problems are likely to result if tires on a dual assembly differ by more than ____ inch in diameter.

1/2"

If a slight mismatch does occur, the smaller of the two tires should be installed on the inside. The most accurate way to measure an inflated tire is to measure the circumference with a steel tape.

Decks in Soriano-Tech Class (145):