*TB 88- Air Foam Brush Patrol Flashcards
(32 cards)
Compressed air foam brush patrol:
____ (low/med/high) expansion ratios are suited for putting down barriers, exposure protection and some mop-up applications
Medium
Compressed air foam brush patrol:
____ (low/med/high?) expansion ratios have a wide range of application including flame knockdown, immediate wetting and mop-up.
Low
Compressed air foam brush patrol:
____ (low/med/high) expansion ratios are effective insulators and suited for exposure protection
High
A ___% Class “A” Foam mixture is utilized for aerial water drops on brush fires
.1%
The .1% mixture results from adding approximately 1/3 of a gallon of concentrate to the helicopter water tank after the tank is filled with water
Compressed Air Foam Brush Patrol:
What foam type would best be used for direct application on a fire?
A wet, fluid foam with fast drain time
Compressed Air Foam Brush Patrol:
What foam type would best be used for indirect application (exposure protection). This foam will adhere to walls, eaves, roofs, ect.
A dry foam with slow drain times will adhere to vertical surfaces and provide and insulating layer to exposed combustibles.
Compressed Air Foam Brush Patrol:
When applying dry foam (low drain time) to outside walls, eaves, roofs, etc., A ___ inch foam layer is appropriate.
1/2”
A ____ (fluid/dry?) foam can be utilized to provide a firebreak or to increase the defensible area around a structure.
Fluid foam
Compressed Air Foam Brush Patrol:
The removable CAF system includes a ____ gal WATER tank
150 gal
Compressed Air Foam Brush Patrol:
The removable CAF system includes a ____ gal FOAM tank
10 gal
Compressed Air Foam Brush Patrol:
The removable CAF system includes a ____ gpm water pump
50 gpm
Compressed Air Foam Brush Patrol:
The removable CAF system includes a ____ cfm air compressor.
50 cfm
Compressed Air Foam Brush Patrol:
Do not engage the 4WD “HIGH” mode above speeds of ___ mph and/or if the front wheels are slipping
55 mph
Compressed Air Foam Brush Patrol:
- True or False? To engage “4x4 LOW” setting, you must first bring the vehicle to a complete stop.
- What about for the “4x4 HIGH” setting?
- True
* The “4x4 HIGH” setting can be set while the vehicle is traveling below 55 mph
Compressed Air Foam Brush Patrol:
When driving through water, avoid water higher than the bottom of the ___ (if possible) and proceed slowly.
Hubs
Compressed Air Foam Brush Patrol
What traction shift selection (2wd/4x4 High or Low /overdrive/etc?) is recommended for driving:
On-highway, dry, hard pavement where maximum fuel economy is desired.
2WD overdrive mode
Compressed Air Foam Brush Patrol
What traction shift selection (2wd/4x4 High or Low/overdrive/etc?) is recommended for driving:
On-highway, dry, hard pavement with maximum loads; where steep roads are encountered.
2WD mode
Compressed Air Foam Brush Patrol
What traction shift selection (2wd/4x4 High or Low/overdrive/etc?) is recommended for driving:
On-highway and off highway; unpaved graded (fire road) road surface
4WD high mode
Compressed Air Foam Brush Patrol
What traction shift selection (2wd/4x4 High or Low/overdrive/etc?) is recommended for driving:
Off highway; extreme conditions: unpaved, steep road surfaces; off road, varied terrain: mud, sand, water.
4WD LOW Mode
Compressed Air Foam Brush Patrol
To prevent damage, the electronic shift 4WD is designed to allow up to ___ seconds before the shift command is performed.
45 sec
Compressed Air Foam Brush Patrol
Compressor control #1 in “auto” position:
Under static conditions with pressure between 75 and 120, this control will balance air and water pressures within ___ psi
5 psi
Compressed Air Foam Brush Patrol
Compressor safe temperature range?
What temp will a warning light/alarm activate?
- 100-170°F
* 180°F
Compressed Air Foam Brush Patrol
Engine safe temperature range?
What temp will a warning light/alarm activate?
- 100-220°F
* 220°F
Compressed Air Foam Brush Patrol
What 3 things should be checked if the compressor temp warning light/alarm activates?
(1) Check to see there is water in the tank.
(2) Check the temperature of water in the tank.
(3) Check heat exchanger circuit strainer for clogs.